ENGLISH VERSION in this document: ESPAŅOL: RXRC11xxV2_V1.9G __________________________________________________________________________________________________________________ Cambios y mejoras en las versiones de firmware RXRC11xxV2. 19-5-2010 Digital Micro Devices __________________________________________________________________________________________________________________ V:1.5, se quita el filtro suavizador y de recalculan las tramas para 44-50Hz 1ŠVersion para Hardware de la serie de receptores RXRC11xxV2 V:1.6, Adaptacion y mejoras para RF Atenuador programable 3 pasos de 6dBm max 18dBm Mejora ratio ADC Rssi Mejora control atenuador y mas velocidad control fail safe V:1.7, Revision salidas SPPM: los impulsos de las versiones anteriores eran muy anchos casi 490uSeg. No era compatible con paparazzi, solo con Microdron. Tiempos de servos limitados desde 700us a 2300us con 1.5ms en centro. Se verifica la compatibilidad de la salida PPM con paparazzi y el receptor Futaba R136F V:1.8 ULRS hard WM11500. Adaptacion. Salida SPPM por interrupcion. resolucion:0.1uSeg. repetitibilidad (precision real) 2.5uSeg. Salidas PPM servos por interrupcion. De momento se deja en 10uSeg queda preparado cuando reciba nuevas tramas del TX Revision y cambio forma de entrar en Setup al inicio Rutina Setup no imprimia siempre en el OSD644. Aumento de la resolucion de los timers internos para que los servos y el SPPM cargen menos del 3% del tiempo de proceso Activacion del receptor como radiobaliza en el canal 19, cuando entra en Fail safe. V:1.9 Se activa salida RSSI analogica. Necesita un C de 6.8uF a 22uF segun carga. salida desde 0 a 3V Se compatibiliza con hard RXRC11L. Se activa el filtrado IP. En la seleccion de canal, se activa el filtro IP del TX seleccionado. se puede usar o no el filtro IP. el filtro se borra cuando entras a seleccionar el canal, no se termina y se para el RX. En el Setup, en la seleccion del canal se agiliza. Es mas rapido. Se selecciona automaticamente la banda de 869 y 903Mhz en la seleccion del canal RF V:1.9c 25-8-09 Se activa el uso del CH9 (correccion bug) V:1.9d 21-9-09 Se activa la compensacion de la medida de RSSI en los receptores RXRC11UxxxV2. compensa unos +11dBm de ganancia mayor V:1.9e 13-11-09 SPPM funciona mal (cuando se cambio el sistema de PPM mas preciso) y aņade el tiempo del sincronismo de 390uSeg. Se corrige. se adapta la medida de la rssi para el receptor azul ya que mide -4 dBms menos por la circuiteria interna. Ahora mide los dBm reales en la entrada de antena. no varia sensibilidad. Los cambios en esta version son utiles para los sistemas que usan la salida SPPM (Mikrocopter y Paparazzi) En el receptor azul para mejorar la medida de la recepcion Rssi en dBm V:1.9G 19-5-10 las versiones anteriores 1.19e y 1.19f, tienen un bug en la programacion del Fail safe que fallaba en la grabacion de la configuracion nueva. Esta corregido. ___________________________________________________________________________________________________________________ ATENCION: No carge este firmware si no esta seguro o si no representa mejora sustancial alguna para su sistema. Las cargas de firmware son un proceso delicado. Si no lo necesita, es mejor no realizarlo. ___________________________________________________________________________________________________________________ ENGLISH VERSION: RXRC11xxV2_V1.9G __________________________________________________________________________________________________________________ Changes and improvements in firmware versions RXRC11xxV2. Digital Micro Devices 05/19/2010 __________________________________________________________________________________________________________________ V: 1.5, smoothing filter is removed and recalculated the plots for 44-50Hz Hardware Version 1st series receivers RXRC11xxV2 V: 1.6, Adaptation and improvement RF 3 step programmable attenuator 6dBm 18dBm max RSSI ADC ratio improves Improved speed control dimmer and more fail safe control V: 1.7,Revision SPPM outputs: the impulses of the earlier versions were very wide almost 490uSeg. It was not compatible with paparazzi, only with Microdron. Limited from time to serve with 1.5ms 2300us 700US to center. It verifies the compatibility of the output PPM with paparazzi and Futaba R136F receiver V: 1.8 ULRs WM11500 hard. Adaptation. Output SPPM by interruption. Resolution: 0.1uSeg. repeatability (precision real) 2.5uSeg. Check for interruption servos PPM. For the time left in 10uSeg is prepared when you receive new plots of TX Revision and change shape to enter Setup to top Setup routine does not always printed in the OSD644. Increasing the resolution of the internal timers for SPPM servos and charge less than 3% of processing time Receptor activation as a marker on channel 19, it enters fail safe. V: 1.9 analog RSSI output is activated. Need a 6.8uF to 22uF C according to load. Output from 0 to 3V It is compatible with hard RXRC11L. IP filtering is enabled. In the selection of channel, IP filter is selected TX. may be used or not the IP filter. the filter is cleared when you come to select the channel, is not completed and for the RX. In the Setup, Channel selection in speeding up. Is faster. It automatically selects the range of 869 and 903Mhz on the RF channel selection V: 1.9c 08/09/1925 It enables the use of CH9 (bug correction) V: 09/09/1921 1.9d Compensation is activated RSSI measurement on receivers RXRC11UxxxV2. offset a higher gain +11 dBm V: 1.9e 11/13/2009 SPPM wrong (when they change the system more accurate PPM) and added 390uSeg time synchronism. Fixed. adjusting the measurement of the RSSI for the blue and measuring receptor DBMS -4 least the internal circuitry. Now measure the actual dBm at the antenna input. does not change sensitivity. Changes in this version are useful for systems using output SPPM (Mikrocopter and Paparazzi) Blue on the receiver to improve reception RSSI measurement in dBm V: 1.9g 5/19/1910 V:1.19f & 1.19e earlier versions have a bug in the programming of the fail safe that fails to save the new configuration. This corrected. ___________________________________________________________________________________________________________________ ATTENTION: Do not load this firmware if you are unsure or do not represent a substantial improvement for your system. The firmware loads are a delicate process. If you do not need it, better not do it. ___________________________________________________________________________________________________________________